We are Riddhi Siddhi Impex, a Mumbai-based Titanium Grade 2 Strips manufacturer and supplier, established in 2002. We slit commercially pure titanium strip to ASTM B265 / ASME SB-265 and AMS 4902 in thicknesses of 0.03-5 mm. Our ISO 9001, 14001, and 45001 certified plant holds a monthly supply capacity of 400-500 tonnes and exports with EN 10204 Type 3.1 / 3.2 certificates on request.
Titanium Grade 2 strips are thin, cold-rolled coils of commercially pure titanium, balanced against oxygen capped at 0.25% and iron at 0.30%. The strip carries a density of 4.51 g/cm³, melts near 1665 °C, and resists chlorides, seawater, and oxidising acids at a fraction of steel's weight. Fabricators draw, form, and weld it into plate heat exchanger packs, welded tubes, and pressed components.
As a reliable Titanium Grade 2 Strip supplier and manufacturer, we cold-roll and slit every strip in-house rather than reselling fixed mill widths. Material leaves annealed to ASTM B265, cut to ±0.1 mm in any width from 3 mm to 2000 mm. Buyers choose matte surfaces, and our quality system covers each pass to dispatch.
We provide ASTM B265 Grade 2 titanium strip in annealed condition with matte surfaces and four edge options.
| Parameter | Details |
|---|---|
| Standard | ASTM B265 / ASME SB-265 / ASTM F 67 |
| Aerospace Standard | AMS 4902 |
| Thickness | 0.03 mm to 5 mm |
| Width | 3 mm to 2000 mm |
| Width Tolerance | ±0.1 mm |
| Condition | Annealed (Soft) |
| Supply Forms | Cold rolled (CR) |
| Surface Finish | Matte |
| Edge | Slit edge, Mill edge, Deburred edge, Round edge |
Titanium Grade 2 strip holds up to 0.25% oxygen, the interstitial that lifts strength over Grade 1 while keeping the metal formable. Iron, carbon, nitrogen, and hydrogen stay capped.
| Element | Composition (% max unless stated) |
|---|---|
| Carbon (C) | 0.08 max |
| Iron (Fe) | 0.30 max |
| Hydrogen (H) | 0.015 max |
| Nitrogen (N) | 0.03 max |
| Oxygen (O) | 0.25 max |
| Titanium (Ti) | Balance |
Annealed Titanium Grade 2 strip reaches a 345 MPa minimum tensile strength with 20% elongation, so it deep-draws and roll-forms cleanly. Commercially pure titanium ships annealed, so no hardness temper ladder applies here.
| Property | Value |
|---|---|
|
Tensile Strength, minimum
|
345 MPa (50 ksi) |
|
Yield Strength (0.2% offset), minimum
|
275-450 MPa (40-65 ksi) |
|
Elongation in 50 mm, minimum
|
20% |
International buyers can cross-reference the UNS R50400 strip against their regional standard from the table below. Every ASTM B265 Grade 2 strip we roll meets these designations.
| Country / Standard | Designation |
|---|---|
| USA (UNS) | R50400 |
| Europe (W.Nr) | 3.7035 |
| Japan (JIS) | Class 2 (Type 2) |
| China (GB) | TA2 |
| Russia (GOST) | ВТ1-0 |
These 5 industries specify most of the Titanium Grade 2 strips we slit. Buyers pick the grade for corrosion resistance, low weight, or biocompatibility ahead of raw strength.
Chlor-alkali and acid plants form commercially pure titanium strips into plate heat exchanger packs and welded tubes. Gr2 Titanium Strip shrugs off wet chlorine, hypochlorite, and dilute oxidising acids that pit stainless within weeks. The strip's formability lets fabricators press deep corrugations without cracking the corrosion barrier.
Desalination plants roll Ti Gr 2 strip into flash-chamber and reverse-osmosis heat exchanger plates and seawater pipework. The grade resists chloride pitting and crevice attack in warm brine, where copper alloys thin and fail. A thin-gauge strip also lifts heat transfer across the exchanger pack.
Coastal power stations press Grade 2 titanium strip into surface condenser tubing and heat exchanger plates cooled by seawater. The metal tolerates chloride-laden flow that erodes brass and stainless tubes. Welded titanium tube drawn from our strip runs for decades without measurable wall loss.
Device makers form Grade 2 titanium strip (compliant to ASTM F 67) into surgical instruments, implant components, and diagnostic hardware. The metal is biocompatible, carries an inert oxide surface, and neither leaches nor triggers tissue rejection. Its cold formability suits stamped and drawn parts that must hold tight tolerances.
Airframe and engine builders form CP Ti Grade 2 strip into brackets, ducting, and honeycomb core at a fraction of steel's mass. Supplied against AMS 4902, the strip pairs a useful strength-to-weight ratio with fatigue resistance. Cold rolling to close gauge keeps formed parts consistent across a production run.
Export orders leave from Mumbai and Taloja, packed in wooden cases or on pallets, ready for sea freight.
| Parameter | Details |
|---|---|
| Packaging | Wooden cases, pallet packing |
| Incoterms | FOB, CIF, CFR, EXW Mumbai |
| Dispatch Points | Mumbai and Taloja warehouses |
| Standard Lead Time | 4 to 5 days |
| Urgent Dispatch | 2 to 3 days |
| Payment Terms | Advance, credit, LC |
| Certification | EN 10204 Type 3.1 / 3.2 on request |
Titanium Grade 2 Strips price in India is around ₹1,100 to ₹2,223 per kg. International buyers pay near USD 11.4 to 23.1 per kg. The figure tracks global titanium rates, and thickness, width, finish, and quantity all shift it. Volume discounts apply to bulk orders, so call or WhatsApp us for today's rate.
We roll and slit Titanium Gr 2 strip from 0.03 mm to 5 mm thick, in any width between 3 mm and 2000 mm. Anything thinner than 0.03 mm falls under our titanium Gr 2 foil range.
Titanium Grade 2 slitting coil is made to ASTM B265 / ASME SB-265, with AMS 4902 available for aerospace orders. The grade designation is UNS R50400, W.Nr 3.7035.
Yes, we precision-slit Ti Gr 2 strips from 3 mm to 2000 mm wide, held to ±0.1 mm. Send us your width and thickness, and we cut to it with no fixed standard size.
Grade 2 is commercially pure, so it forms and welds more easily, while Grade 5 (Ti-6Al-4V) adds aluminium and vanadium for higher strength but lower ductility. Grade 2 strip suits corrosion service and deep forming.
You can buy Titanium Grade 2 winding strips in India from us at Riddhi Siddhi Impex. Our Mumbai warehouse holds Ti Gr 2 strip stock ready for dispatch, and we supply across India and export overseas. Phone or WhatsApp us; quotations are provided within 24 hours.
